Pajero II Technical Information Manual 1991 · PYJE9002 PAJERO 91 TIM 1 · страница 62 из 71 · Открыть оригинал PDF ↗

Текст распознан со скана. Числа и обозначения можно сверить с оригиналом ниже.

SET (COAST) SWITCH FUNCTION

SET

When driving within the range of the limit vehicle
speed [approximately40200km/h(25124
mph)];it makes vehicle speed set when the SET
switch is turned from the on-positionto the off
Afterthat;controlstheactuatorforcruise-
COAST
When the SET switch is turned to the on-position
during auto-cruise control the throttle is fully closed
while the SET switch is the on-position, the vehicle
decelerates due to the engine brake and then the
vehicle speed when the SET switch is turned to the
off-positionistakenasthenewsetspeedfor
auto-cruisecontrol.TheCOASTfunctioncande-

controlled driving at that speed. However, if the SET
switch is turned from the on-position t0 the off in
the range over the high speed limit speed [approx-
imately 200 km/h (124 mph)]; the high speed limit
speed is taken as the set speed.

celerateuntil the low speed limit speed [approx-
imately 40 km/h (25 mph)] is reached but if vehicle
speedfallsbelowthat,theCOAST functionis
canceled.In suchcase,the vehicle speed just
before the beginning of COAST function isputinto
memoryas the set speed_

RESUME (ACCEL) SWITCH FUNCTION

RESUME

If the cruise-controlleddrivingspeed is canceled by
thecancel system (refer to the item mentioned
below) during auto-cruise control, the vehicle speed
setbeforethecancellationresumeswhenthe

RESUME switch is turned from the off-position to
the on in the speed range over the low speed limit
speed [approximately 40 km/h (25 mph)] to control
the cruising speed.

ACCEL

Whenthe RESUMEswitchis turned to theon-
position duringauto-cruisecontrolcontinues
acceleration while the switch is in the on-position,
the vehicle speed when the switch is turned to the
off-positiontakenasthenewset speedfor
auto-cruise control,Vehicle can be accelerated to

over the high speed limit speed [approximately 200
km/h (124 mph)] by the ACCEL function but after
the RESUME switch is turned to the off-position, it
decelerates to the high speed limit speed to control
the cruising speed.

CANCEL FUNCTION

When the following signals are input, current to the
motor-driven vacuum pump assembly is cut off and
the auto-cruise control canceled

When CANCEL switch is in on-position

When the stop lamp switch isON:
When the clutch switch isON<MT>
When the inhibitor switch is in neutral <AT>
When vehicle speed is below the low speed
limit speed [approximately 40 km/h (25 mphll:

When vehicle speed falls more than 15 km/h (9
mph) from the speed in memory.

When, duringRESUME functioning,vehicle
speed again falls morethan15km/h (9 mph)
afterresuming to the memorized vehicle speed
minus 10 km/h (6mph) and over
When vehicle speed changes suddenly (0.5G or
more).

When the stop lamp switch input wire is broken.

HIGH SPEED LIMIT FUNCTION

Cruise-controlled driving is not possible at vehicle
speeds exceedingthehighspeedlimit speed
[approximately 200 km/h (124 mph)]:IftheSET
switch is turned tothe on-positionwhenvehicle
speed exceedsthe high speedlimitspeed,200

km/h (124 mph) isputinto memory. At this time,
when the accelerator pedal is released to decelerate
(under high speed limit speed) ,the cruise control
functions to controlcruising at 200 km/h (124 mph):

Оригинальная страница руководства